Clicker Garage Door Keypad Reset: Instructions

Nowadays, once it comes to securing garages, Clicker garage door keypad is the leading choice for all sorts of homeowners. Easy to install and simple to use, the keypad from Clicker seldom lets people down in the course of operation. Still, similar to its contemporaries,  Clicker garage door keypad only opens with a code and it’s a big hassle when users cannot recall it. Needless to say, Clicker garage door keypad reset process attracts special attention from those that own the keypad of Clicker.

How To Reset A Clicker Keypad

How to Reset Clicker Garage Door Keypad without Code | YGDG

You have forgotten the code to your Clicker keypad and like to perform a reset? In that case, you have come to the right place. This article could show you how to reset Clicker garage door keypad in mere moments.

Step 1: Preparation 

Before doing anything, you have to clear the area around the garage door of obstacles. By doing so, you would have no trouble testing the opening and closing motion of the garage door in the end. Next, grab a ladder and proceed to position it under the garage door opener. For most of the time, it’s a good idea to ask someone to hold onto the ladder as you work.

Step 2: Reset The Code

Get on top of the ladder, reach out to the motor unit of the garage door opener and locate the Learn button. For your information, the Learn button is responsible for the programming of accessories, code reset and so on. Depending on the garage door opener, the Learn button may be green, yellow, red/orange, … After you find the Learn button, press and hold it until the light stops illuminating.

Step 3: Reprogram The Code 

Press the Learn button again, which should make the light illuminate again, then enter the new code via the keypad. Naturally, for your own good, it’s best to use something that no one else besides you could have known. When your Clicker keypad accepts the new code, the light is going to blink. That signals the end of the Clicker garage door keypad reset process and you can start using the new code to operate the garage door.

Temporary Code: An Alternative For Travelers 

Garage Door Quote Template | Quote Examples | Quotient

Let’s just say that you plan to go on a holiday trip and want someone to take care of the house in your absence. You have no qualms about sharing the code to your Clicker keypad but there is an issue: you also use that same code for everything.

You trust the person that you ask to come over but don’t want to take too much risk by divulging your “universal” code? Well, you always have the option of resetting Clicker garage door keypad before the trip. After you enter a new code for the keypad, give it to the caretaker and you can head out with confidence. However, if you prioritize convenience,  it’s strongly recommended that you think about creating a temporary code for the occasion.

Once it comes to temporary code, you have to remember two things: number of hours and number of times

Setting up the number of hours

  • Step 1: Enter the code
  • Step 2: Press and hold the * key. Let go of the key after the light on the garage door opener blinks three times
  • Step 3: Enter temporary code. Next, hit Enter and the light on the garage door opener should blink four times
  • Step 4: Enter the number of hours that you want the temporary code to work. The maximum limit is 255 hours.
  • Step 5: Press the * key to conclude your entry. The light on the garage door opener will blink one time as confirmation.

Setting up the number of times 

  • Step 1: Enter the code
  • Step 2: Press and hold the * key. Let go of the key after the light on the garage door opener blinks three times
  • Step 3: Enter temporary code. Next, hit Enter and the light on the garage door opener should blink four times
  • Step 4: Enter the number of times that you want the temporary code to work. The maximum limit is 255 hours.
  • Step 5: Press the * key to conclude your entry. The light on the garage door opener will blink one time as confirmation.

Insights Into A Non-Responsive Clicker Keypad 

Planks by C.H.I. Overhead Doors

So your Clicker garage door keypad won’t respond to your code and you have no idea what to do? Then it’s widely advised that you give these troubleshooting tips and tricks a look

  • Inspect the batteries: Clicker garage door keypad draws power from batteries so when the batteries deplete, its operation would experience disruption. Hence, one of the things to do while troubleshooting a non-responsive Clicker keypad is to replace its batteries.
  • Check out the buttons: Like every other electronic equipment that incorporates buttons, Clicker garage door keypad is unable to respond to outside input if its buttons get stuck. Because of that, you should take your time examining the buttons if your Clicker keypad refuses to accept your code out of the blue.
  • Take wires into account: The sealed nature of the Clicker garage door keypad means its wires rarely come into contact with the outside. However, if elements manage to get in, they could mess up the wires which impair the operation of the keypad as a whole. Depending on the extent of the damages, you may need to grab a new keypad.

FAQs

Garage Door Opener Repair Company ✔️ Get It Fixed Today

How long would a Clicker garage door keypad last?

Generally speaking, the longevity of keypads for garage doors changes from case to case but on average, a Clicker keypad should last between 10 and 15 years. Therefore, if you grab a Clicker keypad, it’s going to be a while before you have to replace it.

Where could I get a Clicker keypad?

Most stores that deal in home improvements carry various garage door keypads so you should be able to get one by one of them. Don’t want to go out of your way for a keypad? In that case, you need to consider ordering your keypad from online retailers such as Amazon, eBay, etc.

Could I open a garage door during power outages? 

Garage door keypads run on batteries so they still allow people to enter codes but garage door openers won’t operate without power. That is why if you wish to to open your garage door during power outages, you need to use the Emergency Release Cord.

 

  • Add Your Comment