- 1 A Guide On Bypassing The Water Level Sensor Of Washing Machines
- 2 Low Water Level: Breakdowns
- 3 FAQs
Designed to calculate the ideal amount of water to use per load, water level sensor is by all accounts an important component in washing machines. Thanks to water level sensor, homeowners could optimize the consumption of water which allows them to cut down utility bills. Nonetheless, despite its effectiveness and efficiency, the water level sensor is far from perfect so its decision is not always to the people’s liking. Thus, while homeowners value water level sensor, most still want to know how to bypass washing machine water level sensor.
A Guide On Bypassing The Water Level Sensor Of Washing Machines
Want to ensure that enough water is available for your laundry but water level sensor keeps getting in the way? In that case, you have come to the right place. This article contains a number of ways to bypass washing machine water level sensor.
Increase The Bulk Of The Load
For your information, to determine the amount of water, the water level sensor of washing machines uses the bulk of the load as a reference. That means the bulkier the load, the more water would be added into the tub. By increasing the bulk of the load, you could trick the washing machine water level sensor into giving your clothes more water than it should. To increase the bulk of the load, you may soak your clothes in water, add towels into the load, etc.
Adjust The Water Level Switch
Instead of bypassing the washing machine water level sensor, you can adjust the water level switch to get more water. In order to access the water level switch on most washing machines nowadays, you have to open the control panel. When you see the water level switch, proceed to use a screwdriver to tighten the screw so as to move the spring-loaded disc inward. That is going to boost the level of water available per load for your laundry.
To prevent the screw from moving out of place, you should secure it using threadlocker.
Set Up A Water Hose
Your washing machine is a top-loading model? Then it’s possible to bypass the water level sensor using a splitter, a hose and hose caps.
In the beginning, disconnect your washing machine from its water source (hot and cold alike). Next, connect the splitter to the water source that you like to use during laundry. Once you manage to secure the splitter to the water source of your choice, you need to connect the wash cycle hose to one of the openings of the splitter. In the last step, connect the remaining opening of the splitter to the water hose.
While doing the laundry, feel free to open the valve to add more water into the tub if you find the current water level insufficient. Use hose caps to seal the hose outside of use.
Use The Bulk Washing Option
As the name suggests, the bulk washing option on modern washing machines permits people to wash large loads of clothes. However, if you think the amount of water that your washing machine provides is inadequate, you could use the bulk washing option for standard loads. To get the most out of the bulk washing option of washing machines, avoid adding more than 15 items per cycle. Assuming that you keep your loads reasonable, the bulk washing option should deliver great results.
Take Advantage Of Manual Controls
In case you don’t know, certain washing machines on that market incorporate manual controls for the level of water. Via such controls, homeowners can raise and lower the water level as they see fit at a moment’s notice. You would be able to determine whether your washing machine comes with manual controls by reading its owner’s manual. Contact the manufacturer of the appliance if you have any questions about its manual controls.
Low Water Level: Breakdowns
Compared to their predecessors, today’s washing machines use much less water to wash clothes. Nonetheless, if the water level of your washing machine takes a plunge out of the blue, it’s widely advised that you consider these possibilities
All in all, the water level sensor of washing machines is a device that consists of a number of circuits. As a result, if one of its circuits sustain damages, the water level sensor would go haywire which leads to inconsistency in the water levels.
- Solution: Get hold of a multimeter to test the water level sensor of your washing machine. If everything is good then you could move on. On the other hand, if the readings indicate damaged circuitry, you have to repair or replace the water level sensor.
Blockage In The Pressure Hose
Over time, plenty of things can build up inside washing machines and that causes blockages. In the case that the pressure hose happens to get blocked, your washing machine may experience difficulty filling with water.
- Solution: First, you must unplug your machine from its power source. Next, locate the pressure hose which is the one connecting to the water level switch. Disconnect the pressure hose from the fittings before taking a look at its interior. If there is a blockage, take care of it at once and put the pressure hose back into its place.
Too Much Detergent
Some people have a habit of adding too much detergent into newly-purchased washing machines. With the detergent absorbing all the water, it’s natural for the water level in the tub to be low.
- Solution: Calculate the amount of detergent per load in advance. Nowadays, quite a few manufacturers of washing machines add suggestions regarding detergent in the owner’s manual of their products.
Which brands make the best washing machines?
The brand of a washing machine rarely affects its performance so there is no need to worry too much about brand. That being said, if you prioritize quality, keep an eye out for models made by Samsung, LG, Kenmore, etc.
How much should I spend on a washing machine?
Modern washing machines reach the market across price points so no matter the shopping budget, you should have several options. Still, remember the rule of thumb: “You get what you pay for”. Don’t expect top-of-the-line features from dirt-cheap washing machines.
What is the power consumption of washing machines?
Overall, different models use different amounts of power but the consumption rate of standard washing machines ranges from 500 to 1,500W. Energy Star models consume less power than non-Energy Star ones.
Hi, I am Matthew Thompson. I have a special love of repairing house and taking care of my small garden. From 2015, I decided to write more about home improvement, repairing – fixing anything in a common house to help people understand & know how to upgrade their own one. With 7 years working in writing for home & garden, I am really happy if any one could drop a comment about my knowledge.
It could be not correct in your case but if you let me know, I am willing to update my article with your recommendation.