Whirlpool Washer Agitates But Won’t Spin: Causes And Solutions

Washing machines on the market nowadays come from a lot of brands but once it comes to consistency, Whirlpool models don’t have many competitors. Able to give a good account of themselves in situations, washers made by Whirlpool seldom let people down in use. That being said, the operating record of Whirlpool washing machines is not flawless and complaints about Whirlpool washer agitates but won’t spin is proof. Needless to say, with their washers being unable to spin, homeowners would have a hard time taking care of laundry.

How To Troubleshoot Whirlpool Washers

Whirlpool FreshCare 8kg Front Load Washing Machine (Carton Damaged)

No matter what you do, your Whirlpool washer won’t spin even though it agitates? If that happens to be the case, this article should be of use to you. Down below is everything that you must keep in mind while troubleshooting Whirlpool washing machines.

Step 1: Think About The Load

Everyone wants to do their laundry as quickly as possible so overloading watching machines is a habit of various homeowners. While a number of washers incorporate bulk washing, most run into issues when they have to deal with unbalanced loads. Because of that, if your Whirlpool washer agitates but won’t spin, you have to consider the current load of clothes as a potential culprit. Try to rearrange the wet clothes evenly then see whether the spin cycles start up.

Step 2: Take Detergent Into Account

Once it comes to detergent, today’s washing machines accept a wide range of products. That being said, if the detergent that you use creates too much foam, it could prevent your washer from spinning. The reason is straightforward: excessive foaming tends to signal the washing machines that the load of clothes is too large. In order to determine if the detergent is at fault here, it’s a good idea to re-wash the entire load using another product.

Step 3: Check Out The Plug 

In the course of operation, washing machines generate a lot of vibrations which may loosen the plug from the outlet. If the plug comes off, the flow of electricity to the washers inevitably experience interruption and that leads to a halt to the spin cycles. Luckily, in the case that a loosened plug is the one behind your washer trouble, you don’t have to do much to address it. By re-securing the plug to the outlet, your Whirlpool washing machine is going to spin like usual once again.

Step 4: Examine The Drain Hose 

All sorts of stuff could make their way into the drain hose of washing machines: pennies, tissues, buttons and others. As a result, over time, there is a chance that blockages would develop inside the drain hose of the washers. Since the drain hose plays a key role in the initiation of the spin cycles, its blockages usually mean washing machines cannot spin as designed. Assuming that a blocked drain hose is the cause of the ordeal, clearing the blockages should allow your washer to resume operation in mere moments.

Step 5: Give Lid Switch A Look

In case you don’t know, Whirlpool washers contain a lid switch that tells them when the lid is closed. As washing machines made by Whirlpool only begin to spin after people close the lid, problems with the lid switch may disrupt the spin cycles. One way to test if you have a damaged lid switch is to open the lid, press down the lid switch and release it. If you fail to hear a “click” sound, proceed to look for a lid switch replacement.

Calling The Pros: Advice

519,000 washing machines urgently recalled - see if your Whirlpool, Hotpoint or Indesit is affected - Birmingham Live

Overall, when your Whirlpool washer agitates but won’t spin, you could address a number of troubles on your own but not all of them. In the case that you have gone through the above steps but there is no sign of improvements, it’s best to call the pros. Messing with things you don’t understand is dangerous as it increases odds of injuries. For instance: the motor of your washer is damaged but if you attempt to replace it without proper knowledge, you can sustain nasty electric shocks.

FAQs

https://www.cnet.com/a/img/6oV00opww7xT1cGvzANhzeWAd_E=/1200x675/2019/01/10/12b01378-b3a9-4a0f-81b1-bd458730b6c2/whirlpool-washer-dryer-1.jpg

Is it wise to use extension cords to power washers? 

If it’s possible, you should set up your washing machine so it can connect directly to a nearby outlet. Using extension cords to power washers usually leads to losses of electricity which prevent appliances from reaching their maximum potential. Besides that, one more piece of accessory means one more thing to take care of. By doing away with the extension cord, you could save plenty of time and effort.

How much water do washing machines use?

Quite a few factors affect the water consumption of washers in the course of operation so lots of estimates exist. On average, today’s washing machines consume between 15 and 20 gallons of water in order to process a load of clothes. It’s noteworthy that Energy Star models consume less water than non-Energy Star ones. Furthermore, if you implement a couple of measures (skip extra rinse, run full loads, etc),  you may cut down the water consumption of your washer.

What must be done to reduce the vibration of washers?

The number one cause of excessive vibration in washing machines is unlevel floor which is why you should check out the surface under your surface. Feel free to apply adjustments to the feet of your washer to restore its balance. In addition to that, as you load clothes into the washing machine, spread everything across the tub instead of clumping them together in one spot. Last but not least, pick up some anti-vibration pads then slide them right under the feet of your washer.

When should I get a new washing machine? 

In general, assuming that you don’t push your washer to the extremes, it’s going to last for years. Nonetheless, if you notice persistent leaking from your washing machine in use, you have to think about getting a replacement. Another sign of washers reaching the end of their service cycle is repeated failure to fill the tub with water. Without water, the spin cycles won’t start and the time it takes to process a load of clothes would stretch out.

 

  • Add Your Comment